Wayne WSS20 Betriebsanleitung PDF herunterladen (Seite 2)

Operating Instructions and Parts Manual

Safety Guidelines

This manual contains information that is

very important to know and understand.

This information is provided for SAFETY

and to PREVENT EQUIPMENT PROBLEMS.

To help recognize this information,

observe the following symbols.

Danger indicates an

imminently hazardous

situation which, if not avoided, WILL result

in death or serious injury.

Warning indicates a

potentially hazardous

situation which, if not avoided, COULD

result in death or serious injury.

Caution indicates a

potentially hazardous

situation which, if not avoided, MAY

result in minor or moderate injury.

Notice indicates

important

information, that if not followed, may

cause damage to equipment.

G eneral Safety Information

CALIFORNIA PROPOSITION 65

This product or its

power cord contains

chemicals known to the State of

California to cause cancer and birth

defects or other reproductive harm.

Wash hands after handling.

GENERAL SAFETY

Do not

use to

pump ﬂ ammable or

explosive ﬂ uids such as

gasoline, fuel oil, kerosene,

etc. Do not use in a ﬂ ammable and/or

explosive atmosphere. Pump should

only be used to pump clear water.

Personal injury and/or property damage

could result.

All wiring must be

performed by a

qualiﬁ ed electrician. Failure to follow

this warning could result in fatal

electrical shock.

If the

basement has water or

moisture on the ﬂ oor, do not

walk on wet area until all

power is turned off. If the shutoff box is in

the basement, call an electrician. Remove

pump and either repair or replace. Failure

to follow this warning could result in fatal

electrical shock.

Do not

expose

battery to sparks or ﬂ ames

as an explosion or ﬁ re could

result.

Battery

acid is

corrosive. Avoid spilling

on skin or clothing. Eye

protection must be worn

when handling the battery.

A ground fault

circuit interrupter is

required.

This pump must only

be used to pump

clear water. This pump is not designed

to handle efﬂ uent, salt water, brine,

laundry discharge or any other

application which may contain caustic

chemicals and/or foreign materials.

Pump damage may occur if used in these

applications and will void warranty.

Back-up Pump Battery

Requirements

1. Use only a new fully charged 12

volt deep cycle battery. Electrolyte

level must be checked and

maintained in accordance with

manufacturer’s guidelines.

2. Battery sizes that will ﬁ t into the

battery box are 24C, 24VCM, 27C,

27CM and 27F.

3. Battery recharge time will be

different at each installation. Under

normal conditions it will take two

to four days to bring a deep cycle

battery back to full charge after it

has been discharged. If electrical

power to the house is lost more

than once a week, consider keeping

a spare, fully-charged battery to

replace an exhausted battery for the

standby sump pump.

Installation

1. Install in a sump pit per the

minimum diameter required (WSS10:

11 inch, WSS20: 12 inch, WSS30: 15

inch in diameter). Construct sump

pit of tile, concrete, steel or plastic.

Position primary pump switch AWAY

from any inlets so that incoming

water does not contact the switch

face. See Figure 1(a) - 1(c).

2. The unit should be located and

rest on a solid, level foundation.

Do not place pump directly on clay,

earth, gravel or sandy surface. These

surfaces contain small stones, gravel,

sand, etc. that may clog or damage

the pump and cause pump failure.

Flood risk. If ﬂ exible

discharge hose is

used, make sure pump is secured in

sump pit to prevent movement. Failure

to secure pump could allow pump

movement and switch interference and

prevent pump from starting or stopping.

3. Using PVC cement and primer,

connect 1-1/4 inch or 1-1/2 inch (only

1-1/2 inch for WSS30) rigid pipe to

the system's discharge ﬁ tting.

Support pump

and piping when

assembling and after installation.

Failure to do so could cause piping to

break, pump to fail, etc. which could

result in property damage and/or

personal injury.

4. Place battery in box. Attach red

cable from battery box control panel

to positive battery terminal. Attach

black cable to the negative terminal.

Place cover on battery box.

www.waynepumps.com

Check valve

24 inch min.

Inlet

pipe

Grounded

Outlet

Grounded

Outlet

11 inch

Diameter

min.

Figure 1 (a)

Discharge pipe

Cap Switch

ON @ 8 inches

OFF @ approx. 3 inches

WSS10

1 2 3 4 5 6 7 ... 35 36

Kommentare zu diesen Handbüchern

Keine Kommentare

Wayne WSS20 Betriebsanleitung Seite 2

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Wasserpumpen Wayne WSS20