Wayne 3018 Bedienungsanleitung Seite 1

OWNER INSTALLATION AND USER MANUAL Series 3000 Models: 3014, 3018, 3018DLX & 3514 Automatic Garage Door Opener For Sectional Overhead Residenti

10 Step Four: Setting The Chain Pull the chain assembly to the front rail bracket. Insert the “U” bolt through the holes in the front rail bracket an

11 Step 1: Attaching Motor Power Head Unit to Rail Before assembly, align sprocket/coupling cogs to match notches of driver gear. Rotate the Motor S

12 Step 3: Attach Unit to Front Wall Bracket Raise the front end of the opener and attach it to the front wall bracket, using the ¼” x 4” hex head bo

13 Step 6: Mounting Door Bracket WARNING: Fiberglass, aluminum and steel doors must be reinforced to prevent damage to the door. Check with your ga-r

14 Step 9: Installing Deluxe Wireless Wall Station (if included) WARNING: Install all wall controls out of the reach of children and in a location w

15 Step 11: Install Wireless Infrared Safety Sensors Wall Mounting Bracket (If Included) Select a mounting position 5 inches above the floor to cent

16 Step 14: Install Wired Infrared Safety Sensor Wall Mounting Brackets Use the following instructions if your opener is equipped with Wired Infra

17 Step 16: Install Wiring for Wired Infrared Safety Sensor Identify which side of the garage door opening (if any) the sun is “likely” to shine o

18 Step 18: Mount Wired Infrared Safety Sensors Attach the sending and receiving units to the “U” brackets by inserting their tabs into their respe

19 Step 20: Wireless Wall Station Security Code Change and Programming Note: The following steps describe the process to change the Wireless Wall St

2 Read These Important Safety Rules Before Proceeding IMPORTANT INSTALLATION INSTRUCTIONS WARNING: To reduce the risk of severe injury or death: READ

20 Step 21: Alignment of the Wireless Infrared Safety Sensors Use the following instructions if your opener is equipped with Wireless Infrared Safet

21 Step 22: Alignment of the Wired Infrared Safety Sensors Use the following instructions if your opener is equipped with Wired Infrared Safety Sens

22 Programming Transmitter to Power Head Unit Note: Do not press any button on the Transmitter until instructed. 1. Press the PROGRAM Switch button

23 Step 24: Connecting Cushion Arm to Trolley Activate opener to bring trolley to factory pre-set close limit (See illustration). Cushion arm assemb

24 Step 26: Connecting Door Arm to Door Door Mounted Bracket Visually align cushion arm connecting hole with middle hole of door bracket by rotatin

25 Step 28: Setting Door Opening Travel Do not use adjustments to compensate for a poorly balanced door. This will interfere with the proper operatio

26 Step 30: Programming Wireless Keyless Entry (If Included) NOTE: To facilitate installation, program the Keyless Entry station to the opener befo

27 Adjustment # 1 Opening and Closing Force This garage door opener is built with a safety system that allows the door to reverse in the close direc

28 Adjustment # 2 Contact Obstruction Sensing (Closing Direction) The opener is designed to automatically reverse the door during closing travel when

29 IMPORTANT SAFETY INSTRUCTIONS WARNING: To reduce the risk of severe injury or death: Before you proceed, please thoroughly read the safety rules on

3 Veuillez lire ces règles de sécurité importantes avant de commencer les travaux IMPORTANT —NOTICE D’INSTALLATION— AVERTISSEMENT –POUR REDUIRE LES

30 HOW TO ACTIVATE THE OPENER WARNING: Never let children operate or play with door controls. Keep remote control away from chil-dren. Use any o

31 HOW TO OPERATE THE WIRELESS WALL STATION (If Included) WARNING: Never let children operate or play with door controls. Keep remote control away fr

32 HOW TO OPERATE THE DOOR MANUALLY – Emergency Release Disconnect WARNING: The door should be fully closed if possible, weak or broken springs could

33 MAINTENANCE OF YOUR OPENER SYSTEM Test door opener monthly. The garage door MUST reverse on contact with a 1 inch high solid test ob-ject on the

34 TROUBLE SHOOTING SECTION SYMPTOM PROBABLE CAUSE CORRECTIVE ACTION Opener won’t work from wall button or radio control. No power to opener. Sho

35 Parts Breakdown Rail Assembly – All Models #. Part # Description #Per Unit #. Part # Description # Per Unit 1a. 296125 Motor Head Rail Angle

36 Parts Breakdown Power Head Assembly And Accessories – All Models #. Part # Description Per Unit #. Part # Description

37 CLASSICDRIVE ACCESSORIES Three Button mini/visor Transmitter Part# 302083 Controls up to 6 doors or wireless ac-cessories. Includes visor clip

38 Pre-drill a 5/64 pilot hole 3/4" deep X . NOTE: This equipment has been tested and found to comply with the limits

39 LIMITED LIFETIME WARRANTY The Manufacturer warrants that the Classicdrive™ garage door opener will be free from defects in materials and wo

4 Automatic Garage Door Opener – For Residential Doors Only FEATURES 1. Open and Close Cycle Control: Allows garage door to be started and stopped

40 Questions? For quick answers and helpful advice, Call Toll Free 1-888-827-3667 Wayne-Dalton Co

5 IMPORTANT PRE-ASSEMBLY CHECK If assembling a motor head unit from a factory sealed box skip this check. Every Power Head Unit is factory tested and

6 Do not plug the power cord into electrical outlet until opener is fully installed and you are instructed to do so in this manual. Door springs, pull

7 The opener is fully packed in one carton. Unpack and inspect contents carefully for any possible shipping damage or missing parts. Do not attempt

8 For Your reference, all hardware has been illustrated. During assembly and installation, please refer to this page to insure you are using the prope

9 WARNING: DO NOT RUN OPENER UNTIL INSTRUCTED TO DO SO! Step One: Rail Assembly Pre-position parts for assembly. Bolt a splice bracket to th